HeatersPlus.com Questions? 1-800-442-2581 |
Our secure online ordering website: www.MorElectricHeating.com.
|
|
Home | Ordering | Contact Us | Heaters | Controls | Accessories | Search | ||
Mor Custom Screw Plug Immersion Heaters
Screw plug immersion heaters are used by the process heat industry for a wide range of applications. This type features a broad selection of screw plug sizes, wattage, materials and junction box types. Screw plug heaters may be threaded directly into a sufficient tank wall or used with a companion coupling.
OPTIONS FOR
SCREWPLUG HEATERS
The following options are available on most screwplug heaters. They are
intended to provide versatility for a wide range of applications and
conditions. Care must be taken in choosing the appropriate heater and
options for your particular application. Consult with one of our sales
engineers for application assistance.
Sheath Material of Heater and Applications:
Thermostat Control (Optional):
Type Tl, SPST, 120/240
VAC
• T1A 40°-104°f (4°-40°c), 16 amperes
• T1B 60°-250°f (15°-121°c), 25 amperes
• TIC 175°-550°f (80°-288°c), 25 amperes
• T1Ja 0°-100°f (-18°-38°c) electronic control, 20 amperes
• T1Jb 50°-250°f (10°-121°c) electronic control, 20 amperes
Type T2, DPST, 120-277
VAC, 30 amperes, 480 VAC 10 amperes
• T2A - 60°-250°f (15°-121°c)
• T2B - 175°-550°f (80°-288°c)
Type T3, 3PDT, 120/240
VAC1, 60°-250°f (15°-121°c), 30 amperes
• Type T3 is a three-pole, snap action control. One line is controlled by the
dial and is ON continuously whenever the dial moves from OFF. The other two
lines are thermostatically controlled and cycle on/off with temperature rise or
fall.
Terminal Enclosure Options:
NEMA 1 General purpose, standard on most models, an indoor enclosure intended primarily to prevent accidental contact of personnel with the enclosed electrical connections. Use where oil, dust, water or fumes are not a problem.
NEMA 1 WITH THERMOSTAT
4" x 4" x 4"
(102mm x 102mm x 102mm)
NEMA 4 Water tight and
dust tight, indoor/outdoor enclosure intended to protect enclosed electrical
connections from splashing water, hose-down, airborne
dust, snow & rain.
NEMA 4X, same as above but enclosure is corrosion resistant for use where fumes or atmosphere is extremely harsh.
NEMA 4 WITH THERMOSTAT
4" x 4" x 3" HIGH
(102mm x 102mm x 76mm)
NEMA 4
4" x 4" x 3" HIGH
(102mm x 102mm x 76i
NEMA 7
EXPLOSION RESISTANT'
3" DIA. x 4" HIGH
(95mm x 63.5mm)
• NEMA 7 Explosion resistant, for use in environments that have been classified "hazardous".
NEMA 7
EXPLOSION RESISTANT*
WITH THERMOSTAT
53/4" DIA. x 4" HIGH
(146mm x 102mm)
High/Low Limit
Options:
Type "J" or "K" thermocouple can be attached to sheath to be used with an
external control & sayfti™ circuit to provide high or low limit control. ''"
note: unless the thermocouple is attached to the upper most element when the
heater is installed, it is possible for the heater to be exposed to air and the
high limit control to NOT sense a dangerous condition.
A bi-metallic thermoswitch can be provided with a variety of pre-set temperature
limits available. * note: this option is to sense a high or low process
temperature NOT to act as a safety device for the heater.
Note:
Installation Recommendations
We are a Distributor of Industrial, Commercial and Residential Heaters and Controls. Always consult manufacturers installation instructions for proper installation of the products or systems shown on this website. © Copyright 1999-2019 Mor Electric Heating Assoc., Inc. MOR
ELECTRIC HEATING ASSOC., INC. |