1. Dryer Cover HO-IW & HO-IC Models: shall be one piece, heavy-duty, rib-reinforced die-cast zinc alloy. It shall be lightweight, unbreakable, rustproof and all exposed surfaces shall be bright chrome plated or finished with chip-proof, electrostatically applied epoxy, and fastened by two chrome plated tamper-proof bolts to a cast zinc alloy wall plate. R76-IW & R76-IC Models: shall be one piece, heavy-duty, rib-reinforced die-cast zinc alloy. It shall be lightweight, unbreakable, rustproof and all exposed surfaces shall be bright chrome plated or finished with chip-proof, electrostatically-applied epoxy, fitted with a fixed, die-cast, chrome plated, zinc alloy nozzle.
2. The wall plates for surface mounted models shall be equipped with (3) 7/8" (22 mm) diameter holes one of which shall be suitable for use with surface conduit, for ease of wiring. Recessed covers shall be fastened by four flat-head, recessed, tamper- proof bolts to wall box. Wall plate shall be fastened to the wall box by four concealed 1/4” (6mm) mounting bolts, and shall be equipped with two knockouts for ease of wiring.
3. HO-IW & HO-IC Models: shall have a chrome plated, die-cast zinc air outlet which shall be fixed to the blower housing and shall be of a design that will not allow foreign objects to enter the dryer. R76-IW & R76-IC Models: shall be equipped with an air inlet opening on the bottom of the casting and covered with a vandal resistant metal protective grill to prevent the entry of foreign objects. A fixed chrome plated, die-cast zinc air outlet nozzle on the front of the cover shall permit a full flow of warm air when in operation, and shall be protected by a cast alloy grating fixed into the blower housing.
4. All internal parts shall be coated according to Underwriters' Laboratories, Inc. requirements.
5. Entire mechanism shall be internally grounded.

1. Motor for 60 Hz units shall be capacitor-initiated, brushless type (for longer life and quiet operation) 1/10 H.P. 3450 R.P.M. with self- lubricating bearings. It shall be insulated by a resilient mounting and shall be protected by a self-resetting thermal switch. Motor for 50 Hz units shall be a universal 1/10 H.P. 4200 R.P.M. at rated load with sealed lubricated ball bearings. It shall be insulated by a resilient mounting. Motor is thermally protected.
2. Fan shall be a large, single inlet centrifugal type for maximum capacity, and shall deliver 180 C.F.M. Fan shall be mounted directly on the motor shaft, and fan and motor unit shall be insulated from dryer with a resilient rubber mounting to obtain maximum dampening effect.
3. The heating element is constructed of Nichrome wire and side mounted on the blower housing, thereby being vandal proof. It shall be protected by an automatic resetting thermostat, which shall open whenever air flow is cut off and shall close when flow of air is resumed. It shall produce an air temperature of 145°F/63°C at a 72°F/22°C ambient room temperature at the outlet.
4. The control assembly is activated by an infrared optical sensor located next to the air outlet. The dryer shall operate as long as hands are moving under the air outlet. There is a 90 second lockout feature, if hands are not removed.

The dryer shall be guaranteed to be free from defects for a period of ten years, except for three years on the control assembly and sensor. Warranty shall include factory performed labor as well as the repair or exchange of defective parts, at manufacturer's option.

• Hands On® dryers utilize a maintenance free brushless motor, capacitor initiated for quick starts.
• The air nozzle revolves a full 360 degrees providing easy hand and face drying.
• The air nozzle can also be fixed into a stationary downward position by means of a simple on-sight adjustment.
• Dryer covers are available in either a white epoxy paint or chrome plated finish.
• Custom colors are also available.
• All Hands On model dryers can also be specified to serve as hair dryers, ideal for health clubs, locker-room facilities, resorts and private washrooms.

1. Dryer cover shall be one-piece, heavy-duty, rib-reinforced die-cast zinc alloy. It shall be lightweight, unbreakable, rust-proof, fitted with a chrome plated die-cast zinc alloy push button, a fixed or 360° revolving die-cast, chrome plated, zinc alloy nozzle and a recessed instruction plate.
2. All exposed surfaces shall be bright chrome plated or finished with chip-proof, electrostatically-applied epoxy paint.
3. Surface-mounted covers shall be fastened by two flat head, recessed tamper proof bolts to a cast zinc alloy wall plate. Recessed covers shall be fastened by four flat-head, recessed, tamper-proof bolts to wall box. Wall plate shall be fastened to the wall box by four concealed 1/4" (6mm) mounting bolts, and shall be equipped with three (3) 7/8" (22mm) diameter holes, one of which shall be suitable for use with surface conduit, for ease of wiring.
4. Cover shall be equipped with an air inlet opening on the bottom of the casting and covered with a vandal resistant metal protective grill to prevent the entry of foreign objects. A chrome plated, die-cast zinc air outlet nozzle on the front of the cover shall permit a full flow of warm air when in operation, and shall be protected by a cast alloy grating fixed into the blower housing.
5. All internal parts shall be coated according to Underwriters' Laboratories, Inc. requirements.
6. Entire mechanism shall be internally grounded.

1. Motor for 60 Hz units shall be capacitor-initiated, brushless type (for longer life and quiet operation) 1/10 H.P. 3450 R.P.M. with self-lubricating bearings. It shall be insulated by a resilient mounting and shall be protected by a self-resetting thermal switch 50 Hz units: Motor shall be a universal 1/10 H.P. 4200 R.P.M. at rated load with sealed lubricated ball bearings. It shall be insulated by a resilient mounting. Motor is thermally protected.
2. Fan shall be a large, single inlet centrifugal type for maximum capacity, and shall deliver 150 C.F.M. Fan shall be mounted directly on the motor shaft, and fan and motor unit shall be insulated from dryer with a resilient rubber mounting to obtain maximum dampening effect.
3. The heating element is constructed of Nichrome wire and side mounted on the blower housing, thereby being vandal proof. It shall be protected by an automatic resetting thermostat which shall open whenever air flow is cut off and shall close when flow of air is resumed. The element shall produce an air temperature of 145°F/63°C at a 72°F/22°C ambient room temperature at the outlet.
4. The timer is a state of the art electronic device with an adjustable time cycle. For hand dryers, timers are set at 30 seconds and at 3 minutes for hair drying.

All parts on Hand and Hair Dryers shall be warranted against defective material and/or workmanship for a period of ten years. Warranty shall include factory performed labor as well as the repair or exchange of defective parts at manufacturer's option, and shall include damage due to accidents, misuse or vandalism.

Dimensions: 12 1/2 lg. x 9 34" high x 4" deep (318 mm x 248 mm x 102 mm)
Weight: 20 lbs. (9.0Kgs.)

Dimensions: 12 1/2 lg. x 9 3/4" high x 4" deep (318 mm x 248 mm x 102 mm)
Weight: 20 lbs. (9.0Kgs.)

Secure Online Credit Card Ordering - SSL Encryption
delivery time: typically ships in 5-10 working days or less plus the time of your selected UPS shipping method.  Price below does not include shipping cost which is calculated using your address before entering your credit card number.

[ Home ] [ Up ]

view cart

Mor Electric Heating Assoc., Inc. is a Distributor of Industrial, Commercial and Residential Heaters and Controls.
Always consult manufacturers installation instructions for proper installation of the products or systems shown on this website.

visit our other website for home/office/factory infrared heating:

MOR ELECTRIC HEATING ASSOC., INC.
5880 Alpine Ave. NW • Comstock Park, MI 49321  USA • Tel 616-784-1121 • 800-442-2581 • Fax 616-784-7775 • E-mail sales@heatersplus.com